Wall panel buying guide
Compare compact and foamed
SPC wall panels
Compare SPC panels for walls by weight, joint fit and finish. Our wood-free ABA option pairs dense outer skins with a foamed centre.
What are SPC wall panels?
SPC usually stands for stone plastic composite. Wall panels in this category typically combine mineral filler with a polymer such as PVC. A compact board has a solid core, while a foamed core contains small cells.
A continuous mineral-filled section in the solid board being compared.
Wood-free mineral-filled PVC through the skins and centre.
Illustrative sections, not to scale. Layer thicknesses and finishes vary by selected panel.
- Compare finished panel weight
- Ask for measured kg/m² based on usable coverage at the quoted thickness. Check the weight per panel to plan handling and shipping.
- Dry-fit two sample panels
- Inspect a cut edge and fit two boards with their matching profile. Approve the joint appearance alongside the decor and finish.
- Specify the complete shower system
- Check that the selected panel is approved for the intended exposure. Match the wall preparation, adhesive, joints and perimeter seals to that system.
Foaming lowers density relative to the corresponding unfoamed formulation. Finished weight and performance depend on the complete panel.
Explore the ABA constructionThe ABA collection
A better-looking
reason to change.
Marble, stone and wood looks on a wood-free ABA substrate. Choose the decor and finish for your market.
Explore all panel designsDesign visualisations. Confirm the decor, finish, format and joint on the selected physical sample.
From the face to the final joint
Choose a panel.
Get a defined system.
We help you connect the decorative sample, ABA construction, matching accessories and installation requirements in one buying brief.
Water performance: the evidence and its scope
For the tested configuration, average water absorption and thickness swelling are no more than 0.7% after 24 hours. The tested tongue-and-groove joint showed no leakage in a 24-hour test under a configuration-specific protocol verified by an independent laboratory.
These results apply to the tested panel and assembly. The joining profile pictured here is a separate accessory example, not the tested tongue-and-groove joint. Shower suitability depends on the selected panel, compatible materials and sealed joints, corners, perimeters and penetrations.
Review the scoped technical evidence and the complete shower-panel system.
Technical comparison of standard and foamed SPC
Open the detail your buying team needs. Compare the selected panels, their usable coverage and matching evidence.
What the SPC name establishes
Stone polymer composite is another common name for SPC. Ask for the materials and cross-section of the quoted wall panel. Mineral content, density and bending stiffness vary by construction.
Compact and foamed constructions can share a polymer and mineral filler while arranging material differently. Foaming introduces cells and lowers density relative to the corresponding unfoamed formulation. Finished weight depends on thickness, skins, backing and decorative layers as well.
Lightweight SPC and foamed SPC also appear in flooring. Floor click systems and their performance data must be evaluated in their own application. A flooring claim does not approve a wall-panel joint or shower installation.
Compare standard SPC and foamed SPC side by side
Scroll across to compare both panels.
| Buying decision | Standard compact SPC reference | Foamed SPC or foamed ABA option |
|---|---|---|
| Core section | Compact, non-cellular board in this comparison. | Cellular core; an ABA option adds distinct outer skins. |
| Panel weight | Measure kg/m² and kg per panel at the quoted thickness. | Use the same measurements, including all skins and finishes. |
| Bending behaviour | Compare full-size handling and matching test conditions. | Compare the whole section, including skin thickness and core behaviour. |
| Joint machining | Check the actual profile, tolerances and cut quality. | Check profile support, edge damage and fit in the cellular or layered section. |
| Visible finish | Approve the exact decor, coating and joint appearance. | Approve the same items independently of the core description. |
| System evidence | Match fire, water and fitting evidence to the supplied board. | Match evidence to this construction; an alternative core or skin can change the covered product. |
How to compare a sandwich with a compact board
The outer skins and their separation through the panel thickness contribute to bending behaviour. The core supports the skins and transfers forces between them. The result depends on skin properties, core properties, bonding and geometry.
A lighter core does not establish that a panel is universally stronger, weaker or more impact-resistant. Compare the finished assemblies at the same relevant dimensions, support conditions and test method. Use the technical guide to check which evidence covers the selected version.
Density, panel weight and transport calculations
For a uniform material, thickness in millimetres multiplied by density in kg/m³ and divided by 1000 gives mass in kg/m². A sandwich requires the individual layer masses, including any finish and backing, or a measured finished-panel value.
For the same panel, weight divided by overall face area and weight divided by usable installed coverage can give different results. State which area is used, particularly where a connection reduces cover width.
Lower panel mass can help handling and payload planning. It does not guarantee a fixed freight saving. Check whether the shipment is limited by gross weight, packed volume, protection requirements or loading arrangement.
Separate a profile illustration from system approval
The joining-profile example shows how an accessory can cover two flat panel edges. Other panels use a machined tongue-and-groove connection. Confirm the exact profile and the associated sealing detail for the supplied board.
Water resistance of the board does not establish the water performance of the assembled wall. Review the applicable fitting sequence and the complete shower-panel specification.
Compare the installed area and shipped range
Use measured kg/m² and price per usable m². Include cutting waste, profiles and the chosen fixing system. Check panels per pack, gross pack weight, pallet dimensions and loading limits.
Ask for a real two-board joint trial. Check the connection and edge after cutting and dry fitting, substrate and adhesive compatibility, support and movement allowances. For showers, approve corners, tray edges and sealed penetrations with the selected system.
Questions buyers ask
Is every foamed SPC wall panel an ABA panel?
Foamed describes a cellular material, while ABA describes an outer-layer, core, outer-layer arrangement. They can describe the same panel when it has both features. Confirm the cross-section instead of assuming the two names are interchangeable.
Is foamed SPC always lighter than standard SPC?
Foaming reduces density relative to the corresponding unfoamed formulation. Finished boards may have different thicknesses, formulations, skins and backings. Compare measured mass per square metre at the format being purchased.
Is solid SPC always stronger than foamed SPC?
There is no universal ranking from the names alone. Strength, stiffness, impact behaviour and edge performance are different properties. Compare the relevant test results for complete panels under equivalent conditions.
Is foamed SPC the same as PVC-UE?
PVC-UE identifies cellular unplasticised PVC. SPC is a trade description for a mineral-filled polymer composite. Their use can overlap for a particular declared formulation, but the labels do not prove equivalence. Read the PVC-U vs PVC-UE and foamed PVC guide and confirm the actual material.
Can SPC wall panels be used in a shower?
Choose a panel and fitting system documented for the intended shower exposure. Confirm the substrate, adhesive and sealing details at joints, corners, tray or bath edges and penetrations. See the shower wall panel guide for the system details to specify.
Can the same decorative design be supplied on either core?
Ask for the available decor, finish, format and core combination. A similar visual appearance does not confirm an identical surface, joint, performance classification or production specification. Approve the finished sample for the selected version.
Wholesale & private label
See the finish.
Feel the difference.
Share your market, wall or shower application and target range. We will help define the sample, panel specification and accessories to review.
Browse the online catalogue and note the decor names for your sample comparison.
How we build your ABA collectionWhat to include in a sample comparison
- A labelled cut edge and written materials for the skins, core and decorative surface.
- Exact dimensions, usable coverage and measured mass for the quoted format.
- Two boards and matching accessories for a joint trial, plus a full-size panel for handling and cutting.
- The matching technical evidence and installation instructions for the intended application.
Include destination, target size and indicative order in your brief.
For distributors, importers & private-label brands